Pull more SoC driver updates from Arnd Bergmann:
"These updates came a little late, or were based on a later 6.18-rc tag
than the others:
- A new driver for cache management on cxl devices with memory shared
in a coherent cluster. This is part of the drivers/cache/ tree, but
unlike the other drivers that back the dma-mapping interfaces, this
one is needed only during CPU hotplug.
- A shared branch for reset controllers using swnode infrastructure
- Added support for new SoC variants in the Amlogic soc_device
identification
- Minor updates in Freescale, Microchip, Samsung, and Apple SoC
drivers"
* tag 'soc-drivers-6.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
soc: samsung: exynos-pmu: fix device leak on regmap lookup
soc: samsung: exynos-pmu: Fix structure initialization
soc: fsl: qbman: use kmalloc_array() instead of kmalloc()
soc: fsl: qbman: add WQ_PERCPU to alloc_workqueue users
MAINTAINERS: Update email address for Christophe Leroy
MAINTAINERS: refer to intended file in STANDALONE CACHE CONTROLLER DRIVERS
cache: Support cache maintenance for HiSilicon SoC Hydra Home Agent
cache: Make top level Kconfig menu a boolean dependent on RISCV
MAINTAINERS: Add Jonathan Cameron to drivers/cache and add lib/cache_maint.c + header
arm64: Select GENERIC_CPU_CACHE_MAINTENANCE
lib: Support ARCH_HAS_CPU_CACHE_INVALIDATE_MEMREGION
soc: amlogic: meson-gx-socinfo: add new SoCs id
dt-bindings: arm: amlogic: meson-gx-ao-secure: support more SoCs
memregion: Support fine grained invalidate by cpu_cache_invalidate_memregion()
memregion: Drop unused IORES_DESC_* parameter from cpu_cache_invalidate_memregion()
dt-bindings: cache: sifive,ccache0: add a pic64gx compatible
MAINTAINERS: rename Microchip RISC-V entry
MAINTAINERS: add new soc drivers to Microchip RISC-V entry
soc: microchip: add mfd drivers for two syscon regions on PolarFire SoC
dt-bindings: soc: microchip: document the simple-mfd syscon on PolarFire SoC
...
The QiLai implementation of this cache controller uses a cache-sets of
2048, and mandates it in an if/else block - but the definition of the
property only permits 1024. Add 2048 as an option, and deny its use
outside of the QiLai.
Fixes: 51b081cdb9 ("dt-bindings: cache: add QiLai compatible to ax45mp")
Reviewed-by: Ben Zong-You Xie <ben717@andestech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
RISC-V cache drivers for v6.16
SiFive:
Add support for the Eswin EIC7700 SoC, which needs to make sure of the
non-standard cache-ops provided by the ccache driver.
Bindings:
Conversions for two Marvell bindings to yaml, and additions of two
soc-specific compatibles to the axm45mp bindings.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-cache-for-v6.16' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
dt-bindings: cache: add QiLai compatible to ax45mp
dt-bindings: cache: Convert marvell,tauros2-cache to DT schema
dt-bindings: cache: Convert marvell,{feroceon,kirkwood}-cache to DT schema
dt-bindings: cache: add specific RZ/Five compatible to ax45mp
cache: sifive_ccache: Add ESWIN EIC7700 support
dt-bindings: cache: sifive,ccache0: Add ESWIN EIC7700 SoC compatibility
Link: https://lore.kernel.org/r/20250516-liability-facility-667fc14a2a85@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a new compatible string for ax45mp-cache on QiLai SoC.
Also, add allOf constraints to enforce specific cache-sets and cache-size
values for qilai-ax45mp-cache.
Signed-off-by: Ben Zong-You Xie <ben717@andestech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Convert the Marvell Feroceon/Kirkwood Cache binding to DT schema format.
Use "marvell,kirkwood-cache" for the filename instead as that's only
compatible used in a .dts upstream.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
When the binding was originally written, it was assumed that all
ax45mp-caches had the same properties etc. This has turned out to be
incorrect, as the QiLai SoC has a different number of cache-sets.
Add a specific compatible for the RZ/Five for property enforcement and
in case there turns out to be additional differences between these
implementations of the cache controller.
Acked-by: Ben Zong-You Xie <ben717@andestech.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Document the Last Level Cache Controller on IPQ5424. The
'broadcast' register space is present only in chipsets that have
multiple instances of LLCC IP. Since IPQ5424 has only one
instance, both the LLCC and LLCC_BROADCAST points to the same
register space.
Hence, allow only '1' reg & reg-names entry for IPQ5424.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Varadarajan Narayanan <quic_varada@quicinc.com>
Link: https://lore.kernel.org/r/20241121051935.1055222-2-quic_varada@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Pull SoC driver updates from Arnd Bergmann:
"Nothing particular important in the SoC driver updates, just the usual
improvements to for drivers/soc and a couple of subsystems that don't
fit anywhere else:
- The largest set of updates is for Qualcomm SoC drivers, extending
the set of supported features for additional SoCs in the QSEECOM,
LLCC and socinfo drivers.a
- The ti_sci firmware driver gains support for power managment
- The drivers/reset subsystem sees a rework of the microchip sparx5
and amlogic reset drivers to support additional chips, plus a few
minor updates on other platforms
- The SCMI firmware interface driver gains support for two protocol
extensions, allowing more flexible use of the shared memory area
and new DT binding properties for configurability.
- Mediatek SoC drivers gain support for power managment on the MT8188
SoC and a new driver for DVFS.
- The AMD/Xilinx ZynqMP SoC drivers gain support for system reboot
and a few bugfixes
- The Hisilicon Kunpeng HCCS driver gains support for configuring
lanes through sysfs
Finally, there are cleanups and minor fixes for drivers/{soc, bus,
memory}, including changing back the .remove_new callback to .remove,
as well as a few other updates for freescale (powerpc) soc drivers,
NXP i.MX soc drivers, cznic turris platform driver, memory controller
drviers, TI OMAP SoC drivers, and Tegra firmware drivers"
* tag 'soc-drivers-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (116 commits)
soc: fsl: cpm1: qmc: Set the ret error code on platform_get_irq() failure
soc: fsl: rcpm: fix missing of_node_put() in copy_ippdexpcr1_setting()
soc: fsl: cpm1: tsa: switch to for_each_available_child_of_node_scoped()
platform: cznic: turris-omnia-mcu: Rename variable holding GPIO line names
platform: cznic: turris-omnia-mcu: Document the driver private data structure
firmware: turris-mox-rwtm: Document the driver private data structure
bus: Switch back to struct platform_driver::remove()
soc: qcom: ice: Remove the device_link field in qcom_ice
drm/msm/adreno: Setup SMMU aparture for per-process page table
firmware: qcom: scm: Introduce CP_SMMU_APERTURE_ID
firmware: arm_scpi: Check the DVFS OPP count returned by the firmware
soc: qcom: socinfo: add IPQ5424/IPQ5404 SoC ID
dt-bindings: arm: qcom,ids: add SoC ID for IPQ5424/IPQ5404
soc: qcom: llcc: Flip the manual slice configuration condition
dt-bindings: firmware: qcom,scm: Document sm8750 SCM
firmware: qcom: uefisecapp: Allow X1E Devkit devices
misc: lan966x_pci: Fix dtc warn 'Missing interrupt-parent'
misc: lan966x_pci: Fix dtc warns 'missing or empty reg/ranges property'
soc: qcom: llcc: Add LLCC configuration for the QCS8300 platform
dt-bindings: cache: qcom,llcc: Document the QCS8300 LLCC
...
Schemas for array properties should only have 1 level of array
constraints (e.g. items, maxItems, minItems). Sometimes the old
encoding of all properties into a matrix leaked into the schema, and
didn't matter for validation. Now the inner constraints are just
silently ignored as json-schema array keywords are ignored on scalar
values.
Generally, keep the inner constraints and drop the outer "items". With
gicv3 "mbi-alias" property, it is more appropriately a uint32 or uint64
as it is an address and size depends on "#address-cells".
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240925232409.2208515-1-robh@kernel.org
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Pull SoC driver updates from Arnd Bergmann:
"The updates to the mediatek, allwinner, ti, tegra, microchip, stm32,
samsung, imx, zynq and amlogic platoforms are fairly small maintenance
changes, either addressing minor mistakes or enabling additional
hardware.
The qualcomm platform changes add a number of features and are larger
than the other ones combined, introducing the use of linux/cleanup.h
across several drivers, adding support for Snapdragon X1E and other
SoCs in platform drivers, a new "protection domain mapper" driver, and
a "shared memory bridge" driver.
The cznic "turris omnia" router based on Marvell Armada gets a
platform driver that talks to the board specific microcontroller.
The reset and cache subsystems get a few minor updates to SoC specific
drivers, while the ff-a, scmi and optee firmware drivers get some code
refactoring and new features"
* tag 'soc-drivers-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (122 commits)
firmware: turris-mox-rwtm: Initialize completion before mailbox
firmware: turris-mox-rwtm: Fix checking return value of wait_for_completion_timeout()
firmware: turris-mox-rwtm: Do not complete if there are no waiters
MAINTAINERS: drop riscv list from cache controllers
platform: cznic: turris-omnia-mcu: fix Kconfig dependencies
bus: sunxi-rsb: Constify struct regmap_bus
soc: sunxi: sram: Constify struct regmap_config
platform: cznic: turris-omnia-mcu: Depend on WATCHDOG
platform: cznic: turris-omnia-mcu: Depend on OF
soc: samsung: exynos-pmu: add support for PMU_ALIVE non atomic registers
arm64: stm32: enable scmi regulator for stm32
firmware: qcom: tzmem: blacklist more platforms for SHM Bridge
soc: qcom: wcnss: simplify with cleanup.h
soc: qcom: pdr: simplify with cleanup.h
soc: qcom: ocmem: simplify with cleanup.h
soc: qcom: mdt_loader: simplify with cleanup.h
soc: qcom: llcc: simplify with cleanup.h
firmware: qcom: tzmem: simplify returning pointer without cleanup
soc: qcom: socinfo: Add PM6350 PMIC
arm64: dts: renesas: rz-smarc: Replace fixed regulator for USB VBUS
...
Qualcomm driver updates for v6.11
Support for Shared Memory (shm) Bridge is added, which provides a
stricter interface for handling of buffers passed to TrustZone.
The X1Elite platform is added to uefisecapp allow list, to instantiate
the efivars implementation.
A new in-kernel implementation of the pd-mapper (or servreg) service is
introduced, to replace the userspace dependency for USB Type-C and
battery management.
Support for sharing interrupts across multiple bwmon instances is added,
and a refcount imbalance issue is corrected.
The LLCC support for recent platforms is corrected, and SA8775P support
is added.
A new interface is added to SMEM, to expose "feature codes". One example
of the usecase for this is to indicate to the GPU driver which
frequencies are available on the given device.
The interrupt consumer and provider side of SMP2P is updated to provide
more useful names in interrupt stats.
Support for using the mailbox binding and driver for outgoing IPC
interrupt in the SMSM driver is introduced.
socinfo driver learns about SDM670 and IPQ5321, as well as get some
updates to the X1E PMICs.
pmic_glink is bumped to now support managing 3 USB Type-C ports.
* tag 'qcom-drivers-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (48 commits)
soc: qcom: smp2p: Use devname for interrupt descriptions
soc: qcom: smsm: Add missing mailbox dependency to Kconfig
soc: qcom: add missing pd-mapper dependencies
soc: qcom: icc-bwmon: Allow for interrupts to be shared across instances
dt-bindings: interconnect: qcom,msm8998-bwmon: Add X1E80100 BWMON instances
dt-bindings: interconnect: qcom,msm8998-bwmon: Remove opp-table from the required list
firmware: qcom: tzmem: export devm_qcom_tzmem_pool_new()
soc: qcom: add pd-mapper implementation
soc: qcom: pdr: extract PDR message marshalling data
soc: qcom: pdr: fix parsing of domains lists
soc: qcom: pdr: protect locator_addr with the main mutex
firmware: qcom: scm: clarify the comment in qcom_scm_pas_init_image()
firmware: qcom: scm: add support for SHM bridge memory carveout
firmware: qcom: tzmem: enable SHM Bridge support
firmware: qcom: scm: add support for SHM bridge operations
firmware: qcom: qseecom: convert to using the TZ allocator
firmware: qcom: scm: make qcom_scm_qseecom_app_get_id() use the TZ allocator
firmware: qcom: scm: make qcom_scm_lmh_dcvsh() use the TZ allocator
firmware: qcom: scm: make qcom_scm_ice_set_key() use the TZ allocator
firmware: qcom: scm: make qcom_scm_assign_mem() use the TZ allocator
...
Link: https://lore.kernel.org/r/20240705034410.13968-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This reverts commit f0f99f3718.
QDU1000 has 7 register regions. The earlier commit 8e2506d012
("dt-bindings: cache: qcom,llcc: Add LLCC compatible for QDU1000/QRU1000")
to add llcc compatible was reflecting the same, but dtsi change for
QDU1000 was not aligning with its binding. Later, commit f0f99f3718
("dt-bindings: cache: qcom,llcc: correct QDU1000 reg entries") was merged
intended to fix this misalignment.
After the LLCC driver refactor, each LLCC bank/channel need to be
represented as one register space to avoid mapping to the region where
access is not there. Hence, revert the commit f0f99f3718 ("dt-bindings:
cache: qcom,llcc: correct QDU1000 reg entries") to align QDU1000 llcc
binding with its dtsi node.
Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20240619061641.5261-3-quic_kbajaj@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
RISC-V cache drivers for v6.8
The SiFive composable cache driver moves to the cache driver
subdirectory from the drivers/soc and grows support for non-coherent
cache operations. The immediate user for these is the jh7100 SoC, that
a rake of people have on VisionFive v1 or Beagle-V Starlight boards.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-cache-for-v6.8' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: errata: Make ERRATA_STARFIVE_JH7100 depend on !DMA_DIRECT_REMAP
riscv: errata: Add StarFive JH7100 errata
soc: sifive: ccache: Add StarFive JH7100 support
dt-bindings: cache: sifive,ccache0: Add StarFive JH7100 compatible
soc: sifive: shunt ccache driver to drivers/cache
Link: https://lore.kernel.org/r/20231221-catatonic-monday-d4c61283b136@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This cache controller is also used on the StarFive JH7100 SoC.
Unfortunately it needs a quirk to work properly, so add dedicated
compatible string to be able to match it.
Signed-off-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Pull SoC driver updates from Arnd Bergmann:
"The highlights for the driver support this time are
- Qualcomm platforms gain support for the Qualcomm Secure Execution
Environment firmware interface to access EFI variables on certain
devices, and new features for multiple platform and firmware
drivers.
- Arm FF-A firmware support gains support for v1.1 specification
features, in particular notification and memory transaction
descriptor changes.
- SCMI firmware support now support v3.2 features for clock and DVFS
configuration and a new transport for Qualcomm platforms.
- Minor cleanups and bugfixes are added to pretty much all the active
platforms: qualcomm, broadcom, dove, ti-k3, rockchip, sifive,
amlogic, atmel, tegra, aspeed, vexpress, mediatek, samsung and
more.
In particular, this contains portions of the treewide conversion to
use __counted_by annotations and the device_get_match_data helper"
* tag 'soc-drivers-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (156 commits)
soc: qcom: pmic_glink_altmode: Print return value on error
firmware: qcom: scm: remove unneeded 'extern' specifiers
firmware: qcom: scm: add a missing forward declaration for struct device
firmware: qcom: move Qualcomm code into its own directory
soc: samsung: exynos-chipid: Convert to platform remove callback returning void
soc: qcom: apr: Add __counted_by for struct apr_rx_buf and use struct_size()
soc: qcom: pmic_glink: fix connector type to be DisplayPort
soc: ti: k3-socinfo: Avoid overriding return value
soc: ti: k3-socinfo: Fix typo in bitfield documentation
soc: ti: knav_qmss_queue: Use device_get_match_data()
firmware: ti_sci: Use device_get_match_data()
firmware: qcom: qseecom: add missing include guards
soc/pxa: ssp: Convert to platform remove callback returning void
soc/mediatek: mtk-mmsys: Convert to platform remove callback returning void
soc/mediatek: mtk-devapc: Convert to platform remove callback returning void
soc/loongson: loongson2_guts: Convert to platform remove callback returning void
soc/litex: litex_soc_ctrl: Convert to platform remove callback returning void
soc/ixp4xx: ixp4xx-qmgr: Convert to platform remove callback returning void
soc/ixp4xx: ixp4xx-npe: Convert to platform remove callback returning void
soc/hisilicon: kunpeng_hccs: Convert to platform remove callback returning void
...
There's a bunch of bindings for (mostly l2) cache controllers
scattered to the four winds, move them to a common directory.
I renamed the freescale l2cache.txt file, as while that might make sense
when the parent dir is fsl, it's confusing after the move.
The two Marvell bindings have had a "marvell," prefix added to match
their compatibles.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230330173255.109731-1-conor@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
